Heavy-duty Liquid Engineered To Protect Pipelines
Liquid engineered to protect pipelines
Today, pipelines operate in some of the most severe environmental
conditions on earth and you can trust fusion-bonded epoxy (FBE)
coatings to perform with excellence at extreme temperatures.
The range of liquid coatings has also been designed to provide you
with total confidence when considering the choice of coating to
protect your pipeline.
From coating new pipe, bends and fittings, valves, girth welds to
repair work, you can turn to for the pipe coating range that has it
Oil - Liquid and powder coatings engineered to protect the internal and
external surfaces of oil pipelines
Husins offers a range of liquid and powder coatings designed to
protect both the internal and external surfaces of oil pipelines.
In addition to coatings for standard operating conditions, Jotun
has developed specialised products for pipelines operating at high
temperatures up to 150°C (302°F), steel requiring low application
temperature cure and aggressive environments such as sour media,
subkha and water reinjection.
Gas – Liquid and powder coatings designed to protect the internal
and external surfaces of gas pipelines
Coatings designed to protect the external surfaces of gas pipelines
as well as improve internal flow efficiency. The product portfolio
of liquid suits a variety of service conditions and environments
including corrosive service.
Water – Liquid and powder developed to protect the internal and
external surfaces water pipelines
Huisins offers a range of liquid for the internal and external
protection of drinking water pipelines as well as those
transporting sea water, raw water, sewage and water-based slurries.
Liquid coating solutions can help seal cement mortar lined pipe to
maintain drinking water purity.
Refined Product – Liquid and powder coatings formulated to protect
the internal and external surfaces of refined product pipelines
Liquid solutions engineered to protect both the internal and
external surfaces of pipelines carrying refined product including
aviation fuel, liquefied petroleum gas (LPG), petrol, kerosene,
diesel oil and fuel oils.
Piling – Liquid and powder coatings used to protect the external
surfaces of piling pipe
High performance coatings, both liquid designed to withstand the
aggressive on and offshore environments encountered by piling pipe.
- A two pack solvent epoxy coal-tar heavy-duty anti-corrosive coating
and it is characterized by excellent resistance to chemicals, water
- VOC less than 50g/L
For inner and outside of concrete pipe heavy-duty anticorrosion.
- Volume Solids 95%±2%
- Finish/Sheen Semi-Gloss
- Typical Film Thickness 900 microns dry ( 950 microns wet)
- Theoretical Coverage :1.05㎡/L at typical film thickness
- Mix Ratio: 1:1(Volume) 1:1 (mass)
- Method of Application
Airless Spray Tip size range 0.45-0.68mm
Output pressure ≥17mpa
Brush/Roller For small area only
- Thinner : Not recommended.
- Drying Information -5°C 5°C 25°C 35°C
Touch Dry 6H 4H 2H 1H
Hard Dry 36H 24H 18H 12H
Pot Life 2H 1H 30min 20min
Overcoatings Data : Substrate Temperature
Overcoated By -5°C 5°C 25°C 35°C
Min Max Min Max Min Max Min Max
725-H53-102 24H 14D 20H 10D 8H 7D 6 H 5D
- Storage :Store in cool and dry conditions, Well ventilate. Keep
away from hot and fire.
Shelf Life: 12Months minimum at 25°C.Subject to re-inspection
- Pack Size :Park A 25KG/18L in 20L container
Park B 25KG/18L in 20L container.
- Flash Point: Park A Greater than 31°C
Park B Greater than 31°
Mixed paint Greater than 31°
Remove loose powder of the cement, attached organisms, mud, oil or
grease and other foreign matter thoroughly
- Apply in good weather. Temperature of the surface to be coated must
be least 3°C above the dew point when the is lower than 85%
- In common with all epoxy base coatings, this product will exhibit
chalking of the film on UV exposure.
- The dry time and over coating interval may change according to the
- Avoiding absorb the solvent steam and paint steam for long time.
Skin and eyes must avoid contacting the paint. Pay attention to
ventilate and fireproof when applying.